Vantage Pro2 Cabled Console Firmware, Direct PC Install

IMPORTANT! This firmware is only for Cabled Vantage Pro2 Consoles manufactured April 2006 or later (product code of #6312C. This will not work on a 6312 Wireless Console). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.80 firmware is installed on consoles manufactured before April 2006.

If you are looking for foreign language versions, please reach out to your local reseller!

Firmware version 3.80

  1. Modified heat index table to better support high temp and high humidity environments.

Firmware version 3.59

  1. Supports new barometer and humidity sensors with better accuracy.

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a radio packet.

Firmware version 3.00

  1. Console times out of the “Receiving From” setup screen after 15 minutes using batteries and 30 minutes using AC power.
  2. Previous versions of firmware allowed a negative ET, now it will clip hourly ET values at 0.
  3. Added leading zero to temp readings between -1.0 and 1.0.
  4. Improved temp and hum index calculations.
  5. Low humidity readings now clipped at 1% and will not show 0%.

Firmware version 1.90

  1. CWOP uploads will now contain 2 min average wind speed, 10 min wind gust and direction of gust, last 15 minutes of rain, last 1 hour of rain and Altimeter. Must also have WeatherLink software v5.9.0 or later to use this feature.
  2. Fixed a bug that caused the barometer value to have a large error after updating to firmware version 1.82

Weather Envoy Cabled Firmware, Direct PC Install

IMPORTANT! This firmware is only for the Cabled Weather Envoy manufactured April 2006 or later (product code of # 6316C. This will NOT work on a 6316). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.15 firmware is installed on consoles manufactured before April 2006.

If you are looking for international versions, please reach out to your local reseller!

VERSION HISTORY

Firmware version 3.80

  1. Modified heat index table to better support high temp and high humidity environments.

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a data packet.

Firmware version 3.00

  1. Previous versions of firmware allowed a negative ET, now it will clip hourly ET values at 0.
  2. Added leading zero to temp readings between -1.0 and 1.0.
  3. Improved temp and hum index calculations.
  4. Low humidity readings now clipped at 1% and will not show 0%.

Weather Envoy Wireless Firmware, Direct PC Install

IMPORTANT! This firmware is only for the Wireless Envoy manufactured April 2006 or later (product code of #6316. This will NOT work on a #6316C). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.15 firmware is installed on Envoys manufactured before April 2006.

If you are looking for foreign language versions, please reach out to your local reseller!

 

VERSION HISTORY

Firmware version 3.80

  1. Modified heat index table to better support high temp and high humidity environments.

Firmware version 3.15

  1. Minor improvements in firmware efficiency.

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a radio packet.

Vantage Pro2 Wireless Console Firmware, Direct PC Install

IMPORTANT! This firmware is only for Wireless Vantage Pro2 Consoles manufactured April 2006 or later (product code of #6312. This will not work on a 6312C Cabled Console). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.15 firmware is installed on consoles manufactured before April 2006.

If you are looking for foreign language versions, please reach out to your local reseller!

Firmware version 3.80

  1. Modified heat index table to better support high temp and high humidity environments.

Firmware version 3.65

  1. Restored “Receiving From” from initial boot screen for easier setup configuration.

Firmware version 3.62

  1. Minor improvements to allow use of new (or alternate)Temp/Hum and Barometer.
  2. Added additional support for international radio frequencies.

 

Vantage Pro2 Updater Firmware

NOTE: This is not Vantage Pro2 console firmware and should not be used to upgrade your Vantage Pro2 console. This file only updates the firmware in a Vantage Pro2 Updater (Davis #6311VP2).

Version History

This February 7, 2006 firmware update has the following changes

  1. Corrects a problem that may cause the Updater to not update a Vantage Pro2 console. The Updater may show a red light and halt

The December 1, 2005 firmware release has the following changes

  1. In order for the “direct from PC firmware update” feature of the Nov, 2005 console firmware to be properly implemented, the Updater must have this latest Updater firmware in it prior to updating a VP2 console
  2. With this Updater firmware, future Updater firmware can be programmed to the Updater directly from a PC without the use of a second Updater

Required: To use this file you will need at least two Vantage Pro2 Updaters (Davis #6311VP2).

Weather Envoy Cabled Firmware, Direct PC (consoles made pre Apr 2006)

NOTE: This firmware is only for a Vantage Pro2 Cabled Weather Envoy (#6316C).

Version History

Firmware version 1.90

  1. CWOP uploads will now contain 2 min average wind speed, 10 min wind gust and direction of gust, last 15 minutes of rain, last 1 hour of rain and Altimeter. Must also have WeatherLink software v5.9.0 or later to use this feature.
  2. Fixed a bug that caused the barometer value to have a large error after updating to firmware version 1.82
  3. Cabled console will now gracefully handle a serial command terminated with two of n or r characters.

Firmware version 1.82

  1. Changed “ALL CLEAR” function so that it does not clear any user-set calibration numbers
  2. Further improved wind speed translation algorithm for increased accuracy
  3. Improved data logging of high wind speed measurements in environments that get poor reception
  4. Fixed a communication problem where the console output an extra “nr” if it received binary data containing a 10 (x0A) or a 13 (x0D). Note: This issue only affects third-party software developers

Firmware version 1.80

  1. Improved wind speed translation algorithm for increased accuracy
  2. Improved digital barometer measurements at very high temperatures

Weather Envoy Cabled Firmware, Direct PC Install

Before You Install

IMPORTANT! This firmware is only for Vantage Pro2 Cabled Weather Envoys manufactured April 2006 or later (#6316C). The Inside Temp, Inside Hum, and Barometer readings will not appear if 3.12 firmware is installed on Envoys manufactured before April 2006.

Version History

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a radio packet.

Firmware version 3.00

  1. Previous versions of firmware allowed a negative ET, now it will clip hourly ET values at 0.
  2. Added leading zero to temp readings between -1.0 and 1.0.
  3. Improved temp and hum index calculations.
  4. Low humidity readings now clipped at 1% and will not show 0%.

Firmware version 1.90

  1. CWOP uploads will now contain 2 min average wind speed, 10 min wind gust and direction of gust, last 15 minutes of rain, last 1 hour of rain and Altimeter. Must also have WeatherLink software v5.9.0 or later to use this feature.
  2. Fixed a bug that caused the barometer value to have a large error after updating to firmware version 1.82

Vantage Pro2 Cabled Console Firmware, Direct PC Install

Before You Install

IMPORTANT! This firmware is only for Vantage Pro2 Cabled Consoles manufactured April 2006 or later (#6312C).

Version History

Firmware version 3.59

  1. Supports new barometer and humidity sensors with better accuracy.

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a radio packet.

Firmware version 3.00

  1. Console times out of the “Receiving From” setup screen after 15 minutes using batteries and 30 minutes using AC power.
  2. Previous versions of firmware allowed a negative ET, now it will clip hourly ET values at 0.
  3. Added leading zero to temp readings between -1.0 and 1.0.
  4. Improved temp and hum index calculations.
  5. Low humidity readings now clipped at 1% and will not show 0%.

Firmware version 1.90

  1. CWOP uploads will now contain 2 min average wind speed, 10 min wind gust and direction of gust, last 15 minutes of rain, last 1 hour of rain and Altimeter. Must also have WeatherLink software v5.9.0 or later to use this feature.
  2. Fixed a bug that caused the barometer value to have a large error after updating to firmware version 1.82

Vantage Pro2 Wireless Console Firmware, Direct PC Install

Before You Install

IMPORTANT! This firmware is only for Vantage Pro2 Wireless Consoles manufactured April 2006 or later (#6312). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.15 firmware is installed on consoles manufactured before April 2006.

Version History

Firmware version 3.15

  1. Minor improvements in firmware efficiency.

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a radio packet.

Firmware version 3.00

  1. Console timesout of the “Receiving From” setup screen after 15 min using batteries and 30 min using AC power.
  2. Previous versions of firmware allowed a negative ET, now it will clip hourly ET values at 0.
  3. Added leading zero to temp readings between -1.0 and 1.0.
  4. Improved temp and hum index calculations.
  5. Low humidity readings now clipped at 1% and will not show 0%.

Weather Envoy Wireless Firmware, Direct PC Install

Before You Install

IMPORTANT! This firmware is only for Vantage Pro2 Wireless Weather Envoys manufactured April 2006 or later (#6316). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.15 firmware is installed on Envoys manufactured before April 2006.

Version History

Firmware version 3.15

  1. Minor improvements in firmware efficiency.

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a radio packet.

Firmware version 3.00

  1. Previous versions of firmware allowed a negative ET, now it will clip hourly ET values at 0.
  2. Added leading zero to temp readings between -1.0 and 1.0.
  3. Improved temp and hum index calculations.
  4. Low humidity readings now clipped at 1% and will not show 0%.