WeatherLinkIP Data Logger Firmware

VERSION HISTORY

Version 1.1.5

  1. Fixes critical bug that affects archive records and console time.

Version 1.1.3

  1. Added protection against unauthorized remote access to the configuration page by requiring the entry of the device key (printed on the product label) when submitting a change request.

Version 1.1.2

  1. Fixed DNS issue. With this upgrade WeatherLinkIP will revert back to the primary DNS following an internet connection failure.

Version 1.1.1

  1. Fixed problem that would cause the data logger to spontaneously stop uploading to weatherlink.com.

Version 1.0.9

  1. Fixed problem with the DNS query that may prevent it from uploading data to the server.
  2. Fixed problem with uploading archive pages to the server.

Version 1.0.8

  1. Fixed a bug that caused the data logger to stop uploading data periodically. This halt in uploading was caused by a PING message sent by some routers.
  2. Changed data upload format to reduce upload bandwidth to the server and fix missing high/low data.
  3. Added support for 2 DNS servers in dynamic IP address mode. If the data logger cannot successfully resolve the WL.com name through the two given DNS servers it will try with the Google public DNS at address 8.8.8.8.Config page always displays the 1st DNS server even if it is using the Google public DNS server.

Version 1.0.7

  1. Further improved reliability of sending archive data to the WeatherLink.com server when packets are fragmented by certain ISPs.
  2. Improved reliability when changing settings in the datalogger configuration page.
  3. Datalogger configuration page now does not allow setting port 80 for communication.
  4. Added “DNS” and “Error” status to the datalogger configuration page.
  5. Added a watchdog reset timer.
  6. Modified ARP so that when the IP address is temporarily changed, the gateway is bypassed.
  7. Fixed a problem when DNS only returns a valid name address but not an IP address.
  8. Console will exit “Receiving from screen” if left there for 15 minutes.
  9. Improved support for CWOP data packets with Vantage Vue.

 

Vantage Vue Console Firmware, Direct PC Install

NOTE: This firmware is only for with a Mfg Code of MB or higher (e.g. MB, MC, etc.) (#6351, 6351M).

Version History

Firmware version 4.30

  1. Modified heat index table to better support high temp and high humidity environments.

Firmware version 4.18

  1. Supports new barometric pressure sensor. It will also support previous barometric sensors with a Mfg
  2. Code of MB or higher (e.g. MB, MC, etc.)

Firmware version 3.00

  1. Updated internal communication between console and data logger for improved performance.

Firmware version 2.14

  1. Solved problem of inadvertent low transmitter battery message. It was displaying as soon as a low voltage was detected, now it will not display unless a low battery has been detected for a full 2 minutes.
  2. Outside humidity no longer displays 0%.
  3. Modified heat index table to match the algorithm used by the WeatherLink software.

Firmware version 2.12

  1. Fixed display of historical yearly rain totals over 812 mm for 0.2 mm rain collectors (highs, lows, and graphs).
  2. Range of LCD contrast adjustment reduced by half.
  3. Now you must be in the Current Weather screen to move to the Receive Diagnostic screen.

Vantage Pro2 Cabled Console Firmware, Direct PC Install

IMPORTANT! This firmware is only for Cabled Vantage Pro2 Consoles manufactured April 2006 or later (product code of #6312C. This will not work on a 6312 Wireless Console). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.80 firmware is installed on consoles manufactured before April 2006.

If you are looking for foreign language versions, please reach out to your local reseller!

Firmware version 3.80

  1. Modified heat index table to better support high temp and high humidity environments.

Firmware version 3.59

  1. Supports new barometer and humidity sensors with better accuracy.

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a radio packet.

Firmware version 3.00

  1. Console times out of the “Receiving From” setup screen after 15 minutes using batteries and 30 minutes using AC power.
  2. Previous versions of firmware allowed a negative ET, now it will clip hourly ET values at 0.
  3. Added leading zero to temp readings between -1.0 and 1.0.
  4. Improved temp and hum index calculations.
  5. Low humidity readings now clipped at 1% and will not show 0%.

Firmware version 1.90

  1. CWOP uploads will now contain 2 min average wind speed, 10 min wind gust and direction of gust, last 15 minutes of rain, last 1 hour of rain and Altimeter. Must also have WeatherLink software v5.9.0 or later to use this feature.
  2. Fixed a bug that caused the barometer value to have a large error after updating to firmware version 1.82

Weather Envoy Cabled Firmware, Direct PC Install

IMPORTANT! This firmware is only for the Cabled Weather Envoy manufactured April 2006 or later (product code of # 6316C. This will NOT work on a 6316). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.15 firmware is installed on consoles manufactured before April 2006.

If you are looking for international versions, please reach out to your local reseller!

VERSION HISTORY

Firmware version 3.80

  1. Modified heat index table to better support high temp and high humidity environments.

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a data packet.

Firmware version 3.00

  1. Previous versions of firmware allowed a negative ET, now it will clip hourly ET values at 0.
  2. Added leading zero to temp readings between -1.0 and 1.0.
  3. Improved temp and hum index calculations.
  4. Low humidity readings now clipped at 1% and will not show 0%.

Weather Envoy Wireless Firmware, Direct PC Install

IMPORTANT! This firmware is only for the Wireless Envoy manufactured April 2006 or later (product code of #6316. This will NOT work on a #6316C). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.15 firmware is installed on Envoys manufactured before April 2006.

If you are looking for foreign language versions, please reach out to your local reseller!

 

VERSION HISTORY

Firmware version 3.80

  1. Modified heat index table to better support high temp and high humidity environments.

Firmware version 3.15

  1. Minor improvements in firmware efficiency.

Firmware version 3.12

  1. Fixed a bug in 3.00 that did not allow the ET alarm to be cleared.
  2. Eliminates occasional WeatherLink communication issue when console is busy receiving a radio packet.

Vantage Pro2 Wireless Console Firmware, Direct PC Install

IMPORTANT! This firmware is only for Wireless Vantage Pro2 Consoles manufactured April 2006 or later (product code of #6312. This will not work on a 6312C Cabled Console). The Inside Temp, Inside Hum, and Barometer readings will not appear if version 3.15 firmware is installed on consoles manufactured before April 2006.

If you are looking for foreign language versions, please reach out to your local reseller!

Firmware version 3.80

  1. Modified heat index table to better support high temp and high humidity environments.

Firmware version 3.65

  1. Restored “Receiving From” from initial boot screen for easier setup configuration.

Firmware version 3.62

  1. Minor improvements to allow use of new (or alternate)Temp/Hum and Barometer.
  2. Added additional support for international radio frequencies.

 

Vantage Vue Console Firmware, Direct PC Install

NOTE: This firmware is only for with a Mfg Code of MB or higher (e.g. MB, MC, etc.) (#6351, 6351M).

Version History

Firmware version 4.18

  1. Supports new barometric pressure sensor. It will also support previous barometric sensors with a Mfg Code of MB or higher (e.g. MB, MC, etc.)

Firmware version 3.00

  1. Updated internal communication between console and data logger for improved performance.

Firmware version 2.14

  1. Solved problem of inadvertent low transmitter battery message. It was displaying as soon as a low voltage was detected, now it will not display unless a low battery has been detected for a full 2 minutes.
  2. Outside humidity no longer displays 0%.
  3. Modified heat index table to match the algorithm used by the WeatherLink software.

Firmware version 2.12

  1. Fixed display of historical yearly rain totals over 812 mm for 0.2 mm rain collectors (highs, lows, and graphs).
  2. Range of LCD contrast adjustment reduced by half.
  3. Now you must be in the Current Weather screen to move to the Receive Diagnostic screen.

WeatherLink: Perception/Wizard/Monitor, Windows

New version of the software which fixes several minor problems. Will update any existing WeatherLink 4.x installation to version 4.04

Required: Use of this version requires purchase of the original retail product.

WeatherLink: Perception/Wizard/Monitor, Mac

New version of the software which insures both Year 2000 and Leap Year compliance. Patch files are contained in a self-extracting file; double click to unstuff the files. Consult the “Read Me” file for information on the latest changes and instructions on applying the patch files.

Required: Use of this version requires purchase of the original retail product.